Fissure Sealant Retention Trial (FSRT)
|ClinicalTrials.gov Identifier: NCT00873990|
Recruitment Status : Unknown
Verified March 2009 by Aga Khan University.
Recruitment status was: Recruiting
First Posted : April 2, 2009
Last Update Posted : April 2, 2009
|Condition or disease||Intervention/treatment||Phase|
|Fissure Sealant Loss||Other: Total etch bonding agent (5th generation) Other: Self etch (7th generation ) bonding agent||Phase 2 Phase 3|
Pit and fissure sealant have been hailed as a highly effective preventive dental treatment since it was introduced first in late 1970s . Sealants have traditionally placed using two step bonding agents based on acid etching with phosphoric acid followed by drying and bonding agent application and curing. Multiple steps in application of bonding agents have been associated with more chances of procedure errors and prolonged procedure time. The newer bonding agents are based on minimizing the number of steps involved with introduction of self etching bonding agents.6th generation adhesives are based on mixing of two components where as the 7th generation adhesives are based on no mix technique.
Previous studies on fissure sealants have focused on conventional etch and rinse bonding agents, there are only few published studies on effectiveness of the self etch bonding agents in retention of fissure sealants in vivo that have targeted the 6th generation adhesive. Feigal and Quelhas reported equivocal results with use of self etching bonding agents in comparison with etch and rinse bonding agents, but their study was limited by smaller sample size. Similar study was conducted by Burbridge which was based on short clinical follow up of 6 month evaluation where Xeno III by Dentsply (6th generation bonding agent) was compared with Prime & Bond (Dentsply). Another study by Venker et al on Adper Prompt L Pop in a school sealant program was based on retrospective review of cases. In light of published literature on (6th generation) self etch bonding agent has been found to be equal or inferior to total etch bonding agents (5th generation). There are no published clinical trials on the retentiong rate comparison of total etch bonding agent with no mix slef etch bonding agents in pit and fissure sealant.
Our study is based on comparison of effectiveness of single step bonding agent (7th generation adhesives) versus two step bonding agent in fissure sealant retention.
|Study Type :||Interventional (Clinical Trial)|
|Estimated Enrollment :||93 participants|
|Intervention Model:||Factorial Assignment|
|Masking:||Double (Participant, Outcomes Assessor)|
|Official Title:||Split Mouth Clinical Trial of Fissure Sealant Retention With Self Etching and Total Etch Bonding Agent|
|Study Start Date :||January 2009|
|Estimated Primary Completion Date :||July 2009|
|Estimated Study Completion Date :||October 2009|
Active Comparator: 1
application of total etch bonding agent ( 5th generation) for placement of resing based pit and fissure sealants.
Other: Total etch bonding agent (5th generation)
Selected teeth would receive prophylaxis with pumice using prophylaxis brushes for 20 seconds. The teeth will be isolated with cotton rolls before application of bonding agent. The tooth selected for etch and rinse bonding system (two step bonding agent) will be treated with 37% phosphoric acid (Total Etch Ivoclar Vivadent) for 15 seconds followed by rinsing for 30 seconds and then drying with air syringe till frosty white appearance is achieved.
Adper Single Bond 2 (3M ESPE) will be applied to occlusal fissure using applicator brushes followed by curing for 10 seconds. Clinpro(3M ESPE) fissure sealant will be applied to pits and fissures and then light cured for 20 seconds.
Other Name: Adper Single bond 3M ESPE
Self etch bonding agent (7th generation) application for placement of resin based pit and fissure sealant
Other: Self etch (7th generation ) bonding agent
For teeth selected for application of self etching bonding agent (Adper Easy Bond 3 M), the bonding agent will be applied to occlusal surface with microbrushes and will be left undisturbed for 20 seconds followed by air drying for 5 seconds and then will be light cured for 10 seconds. Fissure sealant (Clinpro 3M ESPE) will be applied in a similar manner as for etch and rinse group and light cured.
Other Name: Adper Easy bond 3M ESPE
- fissure sealant loss [ Time Frame: 3months ]
- fissure sealant loss [ Time Frame: 6months ]
Please refer to this study by its ClinicalTrials.gov identifier (NCT number): NCT00873990
|Contact: Nadia Aman, BDS||(92)214930051 ext firstname.lastname@example.org, email@example.com|
|Contact: Farhan R Khan, FCPS||(92)214930051 ext firstname.lastname@example.org|
|The Aga Khan University Hospital||Recruiting|
|Karachi, Sindh, Pakistan, 3500|
|Contact: Nadia Aman, BDS (92)214930051 ext 5011 email@example.com|
|Principal Investigator: Nadia Aman, BDS|
|Sub-Investigator: Ali K Khuwaja, FCPS|
|Sub-Investigator: Farhan R Khan, FCPS|
|Principal Investigator:||Nadia Aman, BDS||The Aga Khan University Hospital|